1. Stundenzeiger
2. Minutenzeiger
3. Krone
4. Krone - erster Klick
5. 24-Stunden-Zifferblatt
6. Sekundenzeiger

Einstellen der Uhrzeit: Stellen Sie die Krone auf Position 4 und drehen Sie sie. Der 24-Stunden-Zeiger ist mit dem Hauptstundenzeiger verbunden.

• Uhrwerk: Seiko VH60 Quarz
• Wasserdicht: 3 ATM / 30 Meter
• Features: 24-Stunden-Zeiger
• Batterie: SR920SW
• Glas: Einseitig gewölbtes Mineralglas mit Antireflexionsbeschichtung
• Gehäusematerial: Aluminium
• Uhrenarmband Material: Nylon
• Nickelfrei: Ja
• Max. Handgelenkgröße: 23 cm
• Min. Handgelenkgröße: 14,5 cm
• Breite des Armbands: 22 mm
• Gehäuse-Durchmesser: 42 mm
• Zifferblatt-Durchmesser: 36 mm
• Gehäusedicke: 9 mm
• Kronenhöhe: 4 mm
• Bandanstoß Breite: 22 mm
• Bandanstoß zu Bandanstoß: 49 mm
• Gewicht: 40 g

Most watches have some level of water resistance. If your watch isn’t water resistant, it may be able to handle small splashes, but don’t risk it. If it has a leather band, don’t get it wet.

• Do not move the crown or push any buttons when your watch is in contact with water, as this may let water enter the case.
  
• If your watch is not water resistant, dip a cotton swab in a bowl of warm water with a drop or two of soap in. Squeeze the tip of the cotton swab to remove most of the water and gently rub the case.
  
• If your watch is water resistant, soak a soft cloth in a bowl of warm water with two drops of mild washing-up liquid added. Wring most of the water out of the cloth and gently rub the case with it.
  
  

Nylon ist stabil und pflegeleicht. Bei Sportlern und Abenteurern ist es die erste Wahl, wenn es um Komfort und Strapazierfähigkeit geht, weil es atmungsaktiv, preiswert und sehr leicht ist. Da es sich jedoch um ein gewebtes Band handelt, wird sich Schmutz und Dreck zwischen den Fäden festsetzen, sodass es von Zeit zu Zeit gereinigt werden muss.

1. Wenn Deine Uhr wasserdicht ist, spüle als Erstes die gesamte Uhr mit Wasser in Zimmertemperatur ab.
2. Wenn Deine Uhr nicht wasserdicht oder wasserfest ist, löse das Uhrenarmband aus dem Gehäuse, bevor Du diese Anweisungen befolgst.
3. Tauche das Uhrenarmband einige Minuten in warmes Seifenwasser ein, um Fettablagerungen und andere Verschmutzungen zu entfernen. Tauche das Gehäuse nicht in Wasser, weil der plötzliche Temperaturwechsel die Zahnräder und Federn des Uhrwerks verformen kann.
4. Bei Bedarf kratze den Schmutz mit einer weichen Bürste ab und wiederhole den Vorgang.
5. Lass die Uhr über Nacht lufttrocknen.

• Store your watch in a dark, dry place to avoid corrosion and discolouration of the dial.
• Always replace the battery on a quartz watch as soon as it runs out. With time, an empty battery may start leaking, damaging the watch’s movement.
• Run mechanical watches at least two days a year to prevent gears and cogs from sticking.
• You should always get your watch serviced by a professional every 3 years.

Rule of thumb: Make sure your watch is the last thing you put on and the first thing you take off.

• Take your watch off and store it safely before engaging in any activity that could damage it.
• Take it off before engaging in any activity likely to make you sweat.
• Take it off before you shower, bathe, or go for a swim.
• Take it off before cooking or cleaning.
• Take it off before you go to bed.
• Don’t expose your watch to chemicals such as cologne, sunscreen, perfume, chlorine, hair gel, etc., as these can discolour, stain, or dull surfaces.
• Try to store your watch separately in a soft enclosure to prevent scratching and rubbing.
• If your watch has closures or clasps, close these to prevent tangling.
• Keep your watch stored in a dry, dark place, and avoid heat fluctuation.

To remove and change your watch strap, you’ll need:

• The watch
• A replacement strap
• A soft surface such as a cloth, t-shirt or mouse pad

You may also need:

• A spring bar tool
• Or a sharp pointed object

1. Place your watch on a soft surface. This prevents it from getting scratched or damaged.

2. If your watch has quick-release pins on the underside, push the small lever inward to release the strap.

1. If your watch has drilled lugs – small holes in the lugs extending from the main watch case – use a sharp, pointed object to push the spring bar in and release the strap. Be careful that the spring bar doesn’t slide out of the strap and get lost.

1. If your watch strap has neither of these, use a spring bar tool. This is a small tool with a v-shaped tip. Use it to compress the spring bar from the underside of the strap between the lugs on the right. Using the tool, push down the ridge of the spring bar to release the strap.

First, check the lug width of your new watch to verify that it’s 22 mm. You can find all our watch straps here. Using the filters, select only the matching width to see our selection for your watch.

If your replacement strap has quick-release bars, press the bar inward and slot it into place between the lugs. You’ll feel it ‘lock’ into position.

If your new strap doesn’t have quick-release pins, use the spring bar tool again. Place one end of the pin into place, then use the tool to compress the spring bar as you slot it in place. You’ll feel it ‘lock’ in position.

Remember to take your time and be careful not to scratch the lugs or damage the new watch strap.

If you take care of your watch and keep it stored correctly, you should enjoy years of timekeeping precision. But even with the best care possible, you may find that your watch needs extra attention from time to time.

Take a look at common issues with watches here. If you can’t find what you’re looking for, our great Customer Service Team is only a phone call away.

To keep the warranty on your watch valid, don't expose it to water past the rated limit and make sure you keep the receipt.